electdanabalter.com is reader supported and a participant of the Amazon Affiliate program. We may earn a small commission from any successful purchase through the recommended links, for more details

7 Steps of How To Remove Ignition Lock Cylinder Without Key- Jeep, Ford, Chevrolet & Dodge Ram

The ignition switch lock cylinder designs come in a variety. The original key is required to turn the lock cylinder turn.

In case you lost the original key, it would be essential to know “how to remove ignition lock cylinder without key”. The original key is required to fix the position of accessories efficiently.

The ignition switch is an important part of an automobile, though it is overlooked. These switches are located inside the steering wheel of your dashboard.

However, they are the main components in the car’s system. Sometimes, the switch fails to work, there is a need to remove and replace it.

Besides, this can be done using simple tools such as a screwdriver.

Therefore, the loss of the original key calls for replacing the ignition entire switch assembly and it means lock cylinder replacement.

The ford ignition lock cylinder removal without key complexity makes it difficult to pick an ignition lock cylinder key.

How to Remove Ignition Lock Cylinder Without Key: the Step-by-Step Guides

The ignition switch is overlooked but it is a very essential automobile part. The switches are to the dashboard column and steering wheel side. They are the car starter system’s main components.

Having simple tools is enough to remove the ignition lock cylinder using a screwdriver. Starting a vehicle using a key means the key inserts to start the engine.

The ignition lock cylinder wears over time and it becomes difficult for the car to start.

It is a must to know how to remove ignition lock cylinder not using any kind of key. However, the cylinder may be replaced as per the code of the existing keys of the car.

Step 1 – Drilling

Turn the power drill and use a drill bit in the ignition cylinder key slot to make a hold of the ignition cylinder. Insert your screwdriver and drill the key slot back.

First, remove from the battery terminal the negative cable. Unscrew the screws holding the steering wheel column upper and lower covers.

The battery looks similar to a black box showing negative and positive signs.

After removing the negative cable of the battery ensure it does not contact the terminals accidentally. 

Step 2 – Removing & Disconnecting

Eliminate steering wheel trim. Remove them carefully after wire disconnection from the horn and remove the washer and nut.

On pulling off the steering wheel, you can see the ignition coil cylinder. Based on a model, you may remove the wiper or other switches of the accessory to free the wheel cover of the steering.

Place the ignition key and release from the housing cylinder and slide it out. Set it aside.

Step 3- Using the Screwdriver

Some cylinder locks may need to insert a paper clip into the cylinder end hole to release the cylinder. The steps vary depending on the manual of the owner.

It will require using a small screwdriver to do the anti-rotation beneath the cylinder. Thus, it will come to a normal position.

Rotating the cylinder ensures the slot align and the cylinder comes out of the casing. 

Step 4- The Accessory Position

Set the accessory position of the ignition switch before the ignition module is released. The accessory position is the place before the engagement of the starter.

This is the time it allows the electronics of the vehicle to run without running the engine.

Anyway, you need not force the ignition module.

Step 5- Pressing the Pin

Press inside the release pin on the ignition module. Insert the screwdriver press the release pin from inside.

If your screwdriver is not small enough, use anything thin and long to press the pin.

Ensure it should not be anything brittle. It may break inside and pressing the pin will become troublesome.

Step 6- Removing the Ignition Switch

Slide and switch out the ignition. Release the pressed pin, pull straight the ignition switch from its place. It should come out effortlessly.

In older vehicles, it may get stuck a bit and this is because there will be a lot of debris and dust accumulation around the cylinder.

In case there is a stuck feeling, press the release pin using a screwdriver.

Step 7- Replacing

You can get rebuilt the ignition switch using the same keys. The other option is to buy a new ignition switch. This can be considered if your old switch cannot be rebuilt.

Getting a new switch means you may ask a specific manufacturer dealership to provide new ignition keys.

However, you have to specify the make, year, and model of the vehicle with the VIN number so that the right part is received.

You can also get aftermarket ignition switches from the local auto parts store.

Ignition System: What & Why?

The ignition system is the important system of the I.C. engines. There is a need for the spark-ignition engine to ignite the air-fuel compressed mixture.

Actually, the ignition system serves the purpose as it takes place within the cylinder at the compression stroke end.

An ignition system refers to producing an electric spark in a gasoline engine so that there is a fuel-air mixture to ignite.

The mixture burning within the cylinders creates the force. It is an electrical system carrying the current plug, the electrical current.

Thus, it gives spark at the right time for the air-fuel mixture to ignite.

The ignition system’s basic components are an induction coil, a storage battery, a distributor, a device to give a discharge of high-voltage on time and a spark plug set.

The storage battery delivers a low voltage electric current and it is converted to high voltage. Some systems of ignition conversion control in the output, larger current.

What is a Ignition Lock Cylinder

Learning how to remove ignition lock cylinder without key is a must-learn thing but before that, you have to know what is it and how it does it work.

Plainly speaking, the ignition lock cylinder is the place that your key is inserted into. This mechanical component is important in a car and is required to start your car.

The ford ignition lock cylinder removal without a key that lifts the internal pin to start the ignition and the engine.

However, the ignition lock cylinder gives power to the vehicle. It is located inside the ignition switch.

Thus, the engine gets activated by turning the key on the ignition lock cylinder and the starter motor is activated.

Generally, the ignition lock cylinders are on the steering column right side. That how to change a lock cylinder without the key cylinder is when you wish to start the car engine.

It is to insert a key into the keyhole that is placed behind the steering wheel. It is referred to as muscle memory.

This keyhole serves as the mechanism preventing unwanted people from using the automobile. In fact, the ignition lock cylinder is the second line of defence.

Types of Ignition System

The ignition system that is found within a car makes it go 10 km to 250 km/hr. Each ignition system produces a consistent spark. 

The ignition system is in three types within the vehicle used in the vehicles of modern-day.

  1. Coil on Plug ignition system (Battery ignition system)
  2. Distributor-less Automotive ignition system.
  3. Electronic Ignition System.

These ignition systems ignite to set fire in the combustion chamber to the mixture of compressed air-fuel. They are different in physical make and offer essential power to drive a vehicle.

However, it is expected the spark to take place at the compression stroke end at the right time. Thus, the ignition system functions at low and high speeds efficiently.

  • Coil-On-Plug Ignition System

The Battery ignition system is also referred to as the Coil-on-Plug system. It includes electronic controls within a car with DIS. It has a single coil replacing two cylinders.

Each coil in this system of coil-on-plug ignition uses a single cylinder.

Thus, there is double time to develop a magnetic field to the maximum. However, cars with the COP system can generate stronger sparks and 40,000 to 50,000 volts.

The coil directly mounts on the car spark plug top and receives voltage firing directly.

Thus, spark cables are not required. During the engine cleaning process, there is the possibility of the ignition coils getting damaged due to water.

Hence, the car drivers must ascertain to wrap it in plastic, so that it stays protected while cleaning.

The Coil-On-Plug ignition system in the automotive industry is a popular system for car ignition.

  • Distributor-less Automotive Ignition System

The timing regulation of the ignition system in this distributor-less system relies on the computer and shaft sensors.

It has a crankshaft or near the flywheel or with the Crankshaft sensor. The sensors display the position of the shaft and send it to the computer as information.

It uses coil packs that are multiple ignition coils and they generate the spark for the cylinders. Automotive manufacturers normally prefer this ignition system type.

The Distributor-less system is preferred as it is less expensive and offers high voltage. Thus, it is considered a better alternative for people who do not wish to spend much.

  • Electronic Ignition Systems

The ignition system uses electronic timing devices at the ignition points and is the same as mechanical ignition.

The ford ignition lock cylinder removal without key electronic control module guides the current flow in the ignition and separates it from the distributor.

This ignition system signals a module within the distributor. It is because it receives its prompt through an armature or magnet to operate the control module.

This is the popular ignition system used in cars.

How Does The Ignition Lock Cylinder Work?

Learning how to change a lock cylinder without the key ignition lock cylinder is where the ignition key is inserted. It is a mechanical part to start a vehicle.

It is mounted within the ignition switch that keeps the ignition in lock mode. The key also has anti-theft coding that reads on inserting the key and allows it to start.

In case the ignition lock cylinder fails to turn or the key is not pulled out or inserted inside properly, the key may have worn or bent.

Worn keys are damaged as the pins inside the cylinder lock prevent unlocking and ignition.

Such cylinder locks can be replaced by repairing the locks or there is a need to buy new locks and keys for the trunk and the doors.

It is because you can move your vehicle and bring it to your regular mechanic to get it equipped with a set of new keys.

However, you can opt for a push-button simple start, eliminating the conventional key system.

How to Remove Ignition Lock Cylinder Chevy Without Key: 6 Step Process

A key is a must to start the engine. There are pins and tumblers in Chevy ignition lock cylinder to start the vehicle with the key.

These pins over time get worn out and the cylinder lock fails to turn on inserting the key.

There is a possibility that the key gets broken within the ignition or can get stuck in the ‘on’ position. These are the steps providing details in Chevy.

Firstly, you need tools such as a Power drill, Screw extractor bits, mechanic gloves, screwdriver, and socket wrench set.

Step 1: Disconnect from the car the negative battery cable. It eliminates shock getting risks. If there is an airbag, disable it. Disconnect the airbag electrical connections.

Step 2: Undo the steering column covering using a screwdriver and a socket wrench. Decrease the dashboard panel and access the ignition switch.

Step 3: Release all the electrical connections leading to the ignition switch. 

Step 4: Do away with the ignition switch screws. Unbolt the assembly and the housing of the ignition switch.

Step 5: Check the housing bolt heads, use a power drill to remove the bolts out of the ignition switch.

Step 6: Keep the assemblies and ignition of the locking cylinder and switch ready. Install fresh components in the steering column of the car and introduce it into the ignition switch assembly.

Turn the ignition key into the car, even before introducing the ignition switch, to check the position of the lock cylinder.

Reconnect the negative battery terminal cable to electrical connections, switch on the car and test the ignition switch.

If it cranks properly, you may reconnect the column panels of the steering and the airbag.

How to Remove Ignition Lock Cylinder without Key Ford: 4 Step Process

Firstly, get tools such as wrench 10 mm, Philips head screwdriver #2, socket and driver 8 mm, utility knife, small screwdriver, putty knife, small paper-clip, flathead small screwdriver, vice-grips, clamp, needle-nose pliers, etc.

Step 1: Detach the negative terminal from the battery. You have to work near the airbag. Remove the airbag as well, as you will be working close to the airbag and it may cause injury.

Removing airbag systems takes some time as you have to discharge a capacitor.

Step 2: Remove the cover of the lower dash, the steering column, and get to the ignition lock cylinder. Release the clip and pull gently the lower dash panel cover.

Moreover, remove the upper steering column cover and the steering wheel lever. Pull down and keep screws organized so that putting it back will be easy.

Step 3: Insert the key and turn using a small screwdriver. Pull the key handle and the cylinder will slide out. Try turning the key further and push the screwdriver.

Be careful while pulling the cylinder out. Keep the pins or tumblers in order. Take each black snap-ring of the lock cylinder off and place it aside.

Step 4: Take out the tumblers from the new lock so that you reconfigure it to suit the original key. Use the old cylinder tumblers and match them.

Close the new tumblers and reassemble the cylinder. Insert the key to check the groove. Remove the key and consider switching the cylinder. 

If it does not turn without a key, it means it is done.

How to Remove Ignition Lock Cylinder without Key Dodge: 4 Step Method

Step 1: The ignition lock is on the steering column and is fixed with an active retainer pin.

It means the active pin needs to be depressed to get the ignition unlocked so that it is pulled from the column.

Step 2: The ignition lock should be kept in the ON position, while the active retainer pin can be depressed.

But without a key means, you need to drill out keeping the car lock in On position.

While reaching the active retainer pin, remove the plastic on the steering column that is held by screws.

Step 3: As the plastic column is removed you can see the electrical switch and the lock.

On depressing the active retainer, the lock is released. 

Step 4: Once the lock and switch are removed the active retainer is visible.

Turn to ON position the lock and ensure to depress the active retainer and immediately pull on the lock so that it releases from the switch.

Normal Steps of Ignition Replacement

  • Disconnect the negative battery cable.
  • Remove steering wheel or on tilt columns, remove the shroud from the clip, keeping a position of 9 o’clock.
  • Disconnect wiring. Tilt the column to the down position. Use a chisel at the ignition lock cylinder cap base and break the lock cylinder cap.
  • Remove the cylinder lock and drill from the housing, the shavings.
  • Review the steering column to notice signs of impairment or destruction.

Do the reverse procedure and install the ignition lock cylinder


The ignition system is of three types that the automobile manufacturers make use of in the cars. Each ignition system type has its pros and cons.

Thus, it is your choice to choose the desired ignition system.

Giving a powerful boost to your car engine implies you need these ignition systems and it offers top-notch functionality, while it is also available at affordable and budget ranges.

Some new models feature push-buttons and keyless starting systems. Yet, the ignition lock cylinders are yet common in some.

In case you notice that the lock cylinder does not start or is stuck, it may have a problem.

Moreover, it is best to get a professional technician immediately to inspect the car and to assess if the cylinder needs replacement.

You can do the removal and replacement if you know how to remove ignition lock cylinder without key.

You should also ensure to follow the replacement of the ignition lock cylinder in a proper way.

If you are planning to do it yourself, the best is to place an order for a lock cylinder replacement that is built based on the OEM specifications.

It means you can fit it easily and it will get locked into the chamber perfectly.

Leave a Comment